CCNA COURSE 50% DISCOUNT OFFER:-
100 % Job Oriented Courses
·
The Essentials of CCNA Routing and Switching Webinar Recordings.
·
200-125 CCNA Exam Code
·
100-105 ICND1 Exam Code
·
200-105 ICND2 Exam Code
CCNA
Course Syllabus in Puducherry:-
Networking concepts
- Components of
network – router, switch, hub, bridge etc
- Types of Network
– LAN, MAN, WAN, VPN, PAN & Content Network
- Defining Network
requirements – NIC- Ethernet (CSMA/CD)
- 10/100/1000 mbps
DUPLEX (Half/Full/Auto) – Connecting Media – Coax.
- 10 base 2T –
UTP/STP – CAT 1/2/3..
- Straight
through/cross crimping (only details no practical)
- Fiber optics –
Single/Multimedia
- 100 Base TX/FX
etc – wireless communication.
- Ethernet cabling
Standard.
- Connecting
Devices
- Repeater – Hub –
Switch – Bridge – Topology – Bus/Star/Ring
OSI – Model
- 7 Layers –
Communication between the Layers (Encapsulation & De-encapsulation) –
PDU.
- Layer 2 –
MAC/LLC – 802.3/802.2 (SAP/SNAP) /Ethernet II – Frames
- Broadcast/Collision
domain – point of -Hub/Switch/Router
- L4 – 3way
handshake – windowing – and about – Connectionless
- Packet size [64B
(mini) to 1518B (Max)]
TCP/IP Model & Ipv4
Addressing
- All Layers of
TCP/IP Compound with – OS
- Application
Layer – TFTP/FTP/SMTP/TELNET/SNMP/DNS
- Transport Layer
– TCP/UDP – TCP Segment Format
- 3 way
handshake/windowing – UDP segment Format
- Internet Layer
- IP datagram
format – Protocol No. – TCP 6 – UDP 17
- ICMP – ARP –
RARP
- Introduction to
IP addressing – Class A/B/C/D/E
- Private IP
address – First OCTET range etc.
Subnetting
- Default Subnet
Mask
- Class C
Subnetting & Practice no. given
- Class B
Subnetting & problems
- Class A
Subnetting & problems
Introduction to IPV6
- Introduction
- Host Address
Assignment
- Unicast,
Multicast and other Special ipV6 Addresses
- Configuring ipV6
Routing and Routing Protocols
- Translations
between ipV4 and ipV6
- Summary
Basic of Router &
Configuration
- Selection of
Router & Cabling a Route
- When Router
used – LAN with WAN connect – to connect networks of different IP
- Different
interface of Router – AUI /S0/S1/AUX – console / BRI etc.
- Cables used in
different interfaces/purpose of interfaces
- WAN interface
cable – EIA/TIA – 232/449/530 – V.35 – X.21
- Different CISCO
series – modular/fixed – 10mbps/100 etc
- Straight
through between DTE & DCE
Different modes of
operation & basic commands
- Internal
Components:
- ROM – POST –
BSL – ROM-MONITOR PRG – MINIIOS
- Different
interface of Router – AUI /S0/S1/AUX – console / BRI etc.
- DRAM -Running
Config
- NVRAM – Startup
Config
- Flash MEM – IOS
- Different Modes:
- ROM Monitor –
Reboot Mode – Setup – Exec Model
- Exec Mode
- User -Privilege
– Global – Sub-configuration mode
- Syntax/command
to switch between modes
- Assigning IP
address for -E0-S0-S1
- Enabling/disabling
– console/privilege / vty password
- Mold – command
- Show Config /
start / run / version / flash
- Basic commands
practice
- Changing
between modes – (user-privilege- Global-etc)
- IP address
configuration-E0-S0-S1
- Password –
enabling – encrypting it
- Practice – motd
– show commands – editing commands
- Assigning host
name (for Router)
- Advanced
Commands
- Register value
– X2102 – boot field value/purpose ROM monitor made – password breaking
8th/6th/13th bit of register value importance
- Boot system
flash/network/ROM – config-register (Changing register value) – etc
command purpose Booting sequence – Backup & Recovery – CDP
- Practice an
above commands as well as following
- Telnet –
[ctrl+shift+6]x – disconnect – sh users /Sessions
- Clear lines
resume – [hostname resolving in telnet domain Enabling/disabling etc - no
practical for this alone]
- Overview of
Cisco SDM (Security Device Manager)
IP Routing
- IP Routing,
Static Routing & Default Routing
- IP routing –
static routing – default- dynamic routing
- Providing clock
rate to up the link after identifying DCE by “Sh controllers” command
- Commands/syntax
– Static/default routing
- Static Routing
& Default Routing
- Practical-session
for Static & default routing
- Dynamic Routing
and RIP
- Dynamic Routing
– IGP & EGP
- IGP – RIP-OSPF
– EGRP – EIGRP
- Classes of
Routing Protocol – Distance vector – Link State – Balanced hybrid
- Role of Routing
Protocol – builds/updates/selects & Routes the packet
- Soluting for
Routing loops – Max. loop count – split horizon – Route poison Reverse –
Hold down Timer
- Features of RIP
– distance vector algorithm – RIP V1/V2 – load sharing – metric (depends
– loop count)
- Metric value
depends – loop count – Ticks – delay – Reliability – cost – MTU –
Bandwidth
- Command –
Router RIP Network
- Sh IP route
- Timer value for
RIP– Update/Invalid/ hold down/flush Timer
- RIP V2 &V3
- Dynamic Routing
– RIP Practical
- Dynamic Routing
EIGRP & OSPF V2 & V3
- Limitations of
distance vector algorithm
- Features of
EIGRP and its operations
- Configuring
EIGRP – “Auto-redistribution”
- Verify and
troubleshooting EIGRP
- Features of
OSPF and its operation
- Configuring
single area OSPF
- Verify and
troubleshoot OSPF
- Access List
- Purpose/advantage
of Access-list
- IP [-for a host
– for a network/sub network].
- Std IP
access-list – wild card calculation
- Extd IP access
list
- Switch port ACL
- Step involved
in creating access list
- Applying access
list at the interface – (inbound/outbound)
- Named
access-list for IP
- Access-list in
Telnet sessiont
- IP standard
Access List
- Practical on
- IP Std
access-list
- IP Extended
Access List
- IP Extd
access-list, named access lists
- NAT
- Implement,
Verify & Troubleshoot NAT
- Explain the
Basic Operation Of NAT
- Using
(including CLI/SDM)
- Practicals on
Static NAT, Dynamic NAT and PAT
- Troubleshoot
NAT issues
- WAN Technologies
- WAN Technologies-
Leased Line
- Leased line
- P to P
communication
- HDLC & PPP
protocol-features
- Enabling HDLC
& PPP
- PPP Link
- PPP layer
& its explanation/role
- PAP/CHAP role
- Configuring
PAP/CHAP using commands
- VPN
- Describe VPN
technology
- Importance Of
VPN
- Benefits &
Role
- Impact &
Components
- Frame-Relay
- Packet
Switched Network
- Virtual
circuit – DLCI – Access-link – CRI – FECN – BECN – LMI
- Enabling
Frame-relay
- Inverse ARP
- Configuring
frame-relay for
- Mesh Network
- Star Network
- Combination of
above two
- Switching
- Switching Operation
and Configuration
- Function
–add-learning / Forward-filters the Frame / loop avoidance
- Redundant path
and its problems
- Spanning Tree
Protocol – purpose – its different state
(blocking/listening/learning/forwarding)
- Modes of
operation of switch/Bridge
- Port duplexing
- Switch &
hub – half duplex
- Switch &
Server – full duplex
- CISCO catalyst
switch 1912 & 1924 interface details
- M/K/I modes
- Basic and
advanced commands
- Enabling &
configuring MAC address table
- VLAN
Configuration
- VLAN – ISL –
Trunking
- Enabling Trunking
- Assigning VLAN
No. & name
- Configuring
ports to a specific VLAN
- VTP purpose
- VTP domain
- VTP modes of
operation
- Switching
Technologies (including VTP , RSTP , PVSTP, 802.1q)
- Implement
Basic Switch Security (including Port Security , Trunk access .etc )
- Wireless LAN
- Wireless Intro
& Operation
- Standards
associated with Wireless Media (including WI-FI Alliance, ITU/FCC)
- Ad-hoc mode,
infrastructure mode
- SSID, BSS, ESS
- Basic
Parameters to configure on a Wireless Network
- Wireless
Security Feature’s (WEP, WPA 1 / 2 )
- Implementing
Wireless Networks
More Details of Other Course,
·
The Essentials of CCNA Routing and Switching Webinar Recordings.
·
200-125 CCNA Exam Code
·
100-105 ICND1 Exam Code
·
200-105 ICND2 Exam Code
CCNA
Course Syllabus in Puducherry:-
Networking concepts
- Components of
network – router, switch, hub, bridge etc
- Types of Network
– LAN, MAN, WAN, VPN, PAN & Content Network
- Defining Network
requirements – NIC- Ethernet (CSMA/CD)
- 10/100/1000 mbps
DUPLEX (Half/Full/Auto) – Connecting Media – Coax.
- 10 base 2T –
UTP/STP – CAT 1/2/3..
- Straight
through/cross crimping (only details no practical)
- Fiber optics –
Single/Multimedia
- 100 Base TX/FX
etc – wireless communication.
- Ethernet cabling
Standard.
- Connecting
Devices
- Repeater – Hub –
Switch – Bridge – Topology – Bus/Star/Ring
OSI – Model
- 7 Layers –
Communication between the Layers (Encapsulation & De-encapsulation) –
PDU.
- Layer 2 –
MAC/LLC – 802.3/802.2 (SAP/SNAP) /Ethernet II – Frames
- Broadcast/Collision
domain – point of -Hub/Switch/Router
- L4 – 3way
handshake – windowing – and about – Connectionless
- Packet size [64B
(mini) to 1518B (Max)]
TCP/IP Model & Ipv4
Addressing
- All Layers of
TCP/IP Compound with – OS
- Application
Layer – TFTP/FTP/SMTP/TELNET/SNMP/DNS
- Transport Layer
– TCP/UDP – TCP Segment Format
- 3 way
handshake/windowing – UDP segment Format
- Internet Layer
- IP datagram
format – Protocol No. – TCP 6 – UDP 17
- ICMP – ARP –
RARP
- Introduction to
IP addressing – Class A/B/C/D/E
- Private IP
address – First OCTET range etc.
Subnetting
- Default Subnet
Mask
- Class C
Subnetting & Practice no. given
- Class B
Subnetting & problems
- Class A
Subnetting & problems
Introduction to IPV6
- Introduction
- Host Address
Assignment
- Unicast,
Multicast and other Special ipV6 Addresses
- Configuring ipV6
Routing and Routing Protocols
- Translations
between ipV4 and ipV6
- Summary
Basic of Router &
Configuration
- Selection of
Router & Cabling a Route
- When Router
used – LAN with WAN connect – to connect networks of different IP
- Different
interface of Router – AUI /S0/S1/AUX – console / BRI etc.
- Cables used in
different interfaces/purpose of interfaces
- WAN interface
cable – EIA/TIA – 232/449/530 – V.35 – X.21
- Different CISCO
series – modular/fixed – 10mbps/100 etc
- Straight
through between DTE & DCE
Different modes of
operation & basic commands
- Internal
Components:
- ROM – POST –
BSL – ROM-MONITOR PRG – MINIIOS
- Different
interface of Router – AUI /S0/S1/AUX – console / BRI etc.
- DRAM -Running
Config
- NVRAM – Startup
Config
- Flash MEM – IOS
- Different Modes:
- ROM Monitor –
Reboot Mode – Setup – Exec Model
- Exec Mode
- User -Privilege
– Global – Sub-configuration mode
- Syntax/command
to switch between modes
- Assigning IP
address for -E0-S0-S1
- Enabling/disabling
– console/privilege / vty password
- Mold – command
- Show Config /
start / run / version / flash
- Basic commands
practice
- Changing
between modes – (user-privilege- Global-etc)
- IP address
configuration-E0-S0-S1
- Password –
enabling – encrypting it
- Practice – motd
– show commands – editing commands
- Assigning host name (for Router)
- Advanced
Commands
- Register value
– X2102 – boot field value/purpose ROM monitor made – password breaking
8th/6th/13th bit of register value importance
- Boot system
flash/network/ROM – config-register (Changing register value) – etc
command purpose Booting sequence – Backup & Recovery – CDP
- Practice an
above commands as well as following
- Telnet –
[ctrl+shift+6]x – disconnect – sh users /Sessions
- Clear lines
resume – [hostname resolving in telnet domain Enabling/disabling etc - no
practical for this alone]
- Overview of
Cisco SDM (Security Device Manager)
IP Routing
- IP Routing,
Static Routing & Default Routing
- IP routing –
static routing – default- dynamic routing
- Providing clock
rate to up the link after identifying DCE by “Sh controllers” command
- Commands/syntax
– Static/default routing
- Static Routing
& Default Routing
- Practical-session
for Static & default routing
- Dynamic Routing
and RIP
- Dynamic Routing
– IGP & EGP
- IGP – RIP-OSPF
– EGRP – EIGRP
- Classes of
Routing Protocol – Distance vector – Link State – Balanced hybrid
- Role of Routing
Protocol – builds/updates/selects & Routes the packet
- Soluting for
Routing loops – Max. loop count – split horizon – Route poison Reverse –
Hold down Timer
- Features of RIP
– distance vector algorithm – RIP V1/V2 – load sharing – metric (depends
– loop count)
- Metric value
depends – loop count – Ticks – delay – Reliability – cost – MTU –
Bandwidth
- Command –
Router RIP Network
- Sh IP route
- Timer value for
RIP– Update/Invalid/ hold down/flush Timer
- RIP V2 &V3
- Dynamic Routing – RIP Practical
- Dynamic Routing EIGRP & OSPF V2 & V3
- Limitations of
distance vector algorithm
- Features of
EIGRP and its operations
- Configuring
EIGRP – “Auto-redistribution”
- Verify and
troubleshooting EIGRP
- Features of
OSPF and its operation
- Configuring
single area OSPF
- Verify and troubleshoot OSPF
- Access List
- Purpose/advantage
of Access-list
- IP [-for a host
– for a network/sub network].
- Std IP
access-list – wild card calculation
- Extd IP access
list
- Switch port ACL
- Step involved
in creating access list
- Applying access
list at the interface – (inbound/outbound)
- Named
access-list for IP
- Access-list in
Telnet sessiont
- IP standard
Access List
- Practical on
- IP Std
access-list
- IP Extended
Access List
- IP Extd
access-list, named access lists
- NAT
- Implement,
Verify & Troubleshoot NAT
- Explain the
Basic Operation Of NAT
- Using
(including CLI/SDM)
- Practicals on
Static NAT, Dynamic NAT and PAT
- Troubleshoot NAT issues
- WAN Technologies
- WAN Technologies-
Leased Line
- Leased line
- P to P
communication
- HDLC & PPP
protocol-features
- Enabling HDLC
& PPP
- PPP Link
- PPP layer
& its explanation/role
- PAP/CHAP role
- Configuring
PAP/CHAP using commands
- VPN
- Describe VPN
technology
- Importance Of
VPN
- Benefits &
Role
- Impact &
Components
- Frame-Relay
- Packet
Switched Network
- Virtual
circuit – DLCI – Access-link – CRI – FECN – BECN – LMI
- Enabling
Frame-relay
- Inverse ARP
- Configuring
frame-relay for
- Mesh Network
- Star Network
- Combination of
above two
- Switching
- Switching Operation
and Configuration
- Function
–add-learning / Forward-filters the Frame / loop avoidance
- Redundant path
and its problems
- Spanning Tree
Protocol – purpose – its different state
(blocking/listening/learning/forwarding)
- Modes of
operation of switch/Bridge
- Port duplexing
- Switch &
hub – half duplex
- Switch &
Server – full duplex
- CISCO catalyst
switch 1912 & 1924 interface details
- M/K/I modes
- Basic and
advanced commands
- Enabling &
configuring MAC address table
- VLAN
Configuration
- VLAN – ISL –
Trunking
- Enabling Trunking
- Assigning VLAN
No. & name
- Configuring
ports to a specific VLAN
- VTP purpose
- VTP domain
- VTP modes of
operation
- Switching
Technologies (including VTP , RSTP , PVSTP, 802.1q)
- Implement Basic Switch Security (including Port Security , Trunk access .etc )
- Wireless LAN
- Wireless Intro
& Operation
- Standards
associated with Wireless Media (including WI-FI Alliance, ITU/FCC)
- Ad-hoc mode,
infrastructure mode
- SSID, BSS, ESS
- Basic
Parameters to configure on a Wireless Network
- Wireless
Security Feature’s (WEP, WPA 1 / 2 )
- Implementing
Wireless Networks
Networking Course
CCNA, MCSA, RHCE, Hardware and Networking
Software Course:-
Dot Net, JAVA, C and C++, Tally
Additional Course Making Money Online:-
Very Low Fees of Training to Learn Make Money Online
etc.,
More Details
Networking Course
CCNA, MCSA, RHCE, Hardware and Networking
Software Course:-
Dot Net, JAVA, C and C++, Tally
Additional Course Making Money Online:-
Very Low Fees of Training to Learn Make Money Online
etc.,
More Details
Contact us:-
CGATES
Team IT Solution
169/C, I Floor, Sundraraju Chettiyar Complex,
Cuddalore To Pondy Main Road,
Mudaliarpet, Pondcherry-605004
Phone:-0413-2355051
Cell:-9790582555, 8825255525
No comments:
Post a Comment